Caulking the Deck

 

 
Sealing the Decks for the Summer
One of the best things we can do to keep everyone comfortable on board the J. & E. Riggin is keep things dry. Especially in the cabins. The best way to keep the cabins dry, is to make sure there is plenty of material in between the pine planks that form the deck. The gaps between the planks are called seams and they are packed tightly with cotton and oakum before being sealed with a layer of hot pitch. As the boat sails, it bows and flexes in the water, causing some seams to loosen up over time and begin to leak. In the winter, we do our best to identify problem spots and remove wet material between the planks before replacing it, and sealing it with fresh pitch. This process is called caulking. Captain Schaefer spends a lot of time each winter crawling across the deck fixing seams, so we joined him on deck for a demonstration.

 

 
The Right Tools for the Job
Capt. Schaefer makes his way down to the boat with a milk crate containing caulking cotton, oakum, an assortment of caulking & reefing irons of different thicknesses and lengths, and a caulking mallet. The cotton is just very loosely spun fluffy bales of cotton. Oakum is loosely twisted hemp or jute fiber wet with pine tar. The irons are meant to drive the fibers into the v-shaped gaps between planks when struck by the caulking mallet. A caulking mallet is a wooden mallet designed to minimize damage to the irons and to the joints of the user by absorbing the shock of each impact.

 

 

Probing and Reefing the Seams
Capt. Schaefer begins by poking the seams with the tip of his knife. If the knife fails to penetrate the seam he knows it is still densely packed. If the tip of the knife sinks right in, he knows he has identified a problem spot. He then uses a reefing iron and a rubber mallet to dig into the seam and extract the rotten fiber. Once all of the rotten fiber has been removed, it is time to start filling it again.

 

 
Packing the Seam
Capt. Schaefer chooses the right iron for the seam by inspecting the size of the seam and where it is located. “When I am driving cotton I use a thinner iron to start” he says. He lines up a long strand of cotton and systematically pounds it into the seam, driving it in in small arches that overlap slightly. He will then go back after this initial pass and drive the cotton deeper into the seam.
Once the cotton is in place, he makes a pass with a layer of oakum. “If I am driving oakum, I will use a wider iron which matches the width of the seam I am working on. I even have irons that are slightly bent for those seams that are against the side of a cabin house.” In the same way he drove the cotton, he drives a thick layer of oakum on top so there is only about a quarter of an inch of space from the oakum to the top of the plank.

 

 
 
Sealing the Seam

Now that the seam is packed with fresh fiber, he is ready to add the pitch

and seal it. Captain Schaefer, chisels off a few chunks of pitch from a brick. Pitch is a viscoelastic polymer which is derived from coal tar in the process of its distillation. The pitch is put in a can and heated until it is a liquid. It is poured over the seam and left to harden and cool. Sometimes the word pitch is used interchangeably with the word tar, but tar is generally a bit thinner than pitch, while pitch hardens into a solid.

Once the pitch has hardened any excess is scraped from the surrounding planks. Hopefully, with the problem seams identified and replaced, we will stay cozy and dry in our cabins throughout the summer!
 

Peapod Gets Some Love

The barn is abuzz with winter projects.  While Louis and Chives prep and sand and scrape and fill, Capt. is  busy repairing the peapod.   A couple of summers ago she received some structural damage to her mid-section and while she has held up fairly well under the strain, it was time to address her needs.  

We carry this sweet little row boat on our davits and lower her all summer long for those who want to do a little harbor exploring or catch a bit of exercise to work off Annie’s meals, so she’s pretty important to our summer operations.  In addition, she’s a  Jimmy Steele design, one of the many built by the famous boat builder.  We are lucky to have such a special little vessel and we are happy to be taking good care of her.  

Here’s a little photo journal of the work and care she’s receiving.

wooden boat maintenance
Sistering a couple of frames and shoring up some planking

 

 

wooden boat maintenance
Hey, is that the home stove? And the teapot? Capt. is using both to steam a couple of frames.

 

wooden boat maintenance
Don’t steam the cookbooks! Ahhhh!

 

wooden boat maintenance
Gluing and clamping everything together

 

wooden boat maintenance
Now we wait

 

wooden boat maintenance
The final product – strong and beautiful

 

wooden boat maintenance
And then we add some pretty hardware so she can take us on many more rows this summer.

 

Photos by Captain Jon Finger

Wooden Boats – Winter Projects

While the weather outside fluctuates between spring and the arctic, inside the barn, all is toasty and warm… and busy!  Louis and Chives, long-time Riggin crew, are both ‘on deck’ so to speak and in the barn full-time.  Right now, much of their work is about making dust as they sand and scrape all of the surfaces in preparation for their shiny coats.

wooden boat maintenance
These two goons working away on the barrels – scrape, scrape, scrape

 

wooden boat maintenance
Oars and Captains wheel – gonna be shiny soon!

 

wooden boat maintenance
Hatch covers sanded and ready for the final varnish and paint coats

 

marine engine work
The yawl boat engine removed and transmission ready for a rebuild and reinstall

 

wooden boat maintenance
Spars for Iolaire getting touch ups and undercoats before the final coat goes on

 

Photos by Captain Jon Finger and Elizabeth Poisson